<rt id="iw04y"><small id="iw04y"></small></rt><rt id="iw04y"><small id="iw04y"></small></rt>
<acronym id="iw04y"><center id="iw04y"></center></acronym>
<rt id="iw04y"><small id="iw04y"></small></rt><rt id="iw04y"><small id="iw04y"></small></rt>
<rt id="iw04y"></rt>
<acronym id="iw04y"></acronym>
<sup id="iw04y"></sup>
<acronym id="iw04y"><small id="iw04y"></small></acronym>
"

✅万家电竞|官网 ✅㊣全球最大,最信誉的线上综合平台✅万家电竞|官网 ✅千款游戏,砖石级服务,万家电竞|官网 ,欢迎各界玩家加入体验!

<rt id="iw04y"><small id="iw04y"></small></rt><rt id="iw04y"><small id="iw04y"></small></rt>
<acronym id="iw04y"><center id="iw04y"></center></acronym>
<rt id="iw04y"><small id="iw04y"></small></rt><rt id="iw04y"><small id="iw04y"></small></rt>
<rt id="iw04y"></rt>
<acronym id="iw04y"></acronym>
<sup id="iw04y"></sup>
<acronym id="iw04y"><small id="iw04y"></small></acronym>
"

CKE_Tech (Dongguan) Co.,Ltd.

Professional precision parts CNC cutting high-tech processing

Hotline:+86769-39022898

4Company news

CNC machining center operation points introduction


Cnc machining center operation points introduction

Due to the high technological content of the machining center, it is much more complicated in operation than the ordinary machine tool. It must be operated in strict accordance with the operating procedures to ensure the normal operation of the machine. In addition, the operation speed of the machining center is relatively high, and it is necessary to pre-determine the correctness of the operation instructions and the operation results before executing the operation instructions. Then operate again. In order to avoid accidents.

Vertical Machining Center

First, the cnc machining center before the start of work

1. Turn on the machine's total power supply and CRT monitor power supply, and start the machine tool hydraulic system.

2. Check whether the machine tool has any kind of information on the CRT to eliminate the bitter report and check whether the peripheral equipment of the machine is normal.

3. Check if the position of the machine tool changer and the tool magazine is correct.

4. Check whether the coordinates of the machine tool are in a safe position, including the coordinates must be far away from the machine zero point to prevent the overshoot phenomenon when the coordinate returns to the reference point and ensure that the tool does not interfere with the machined workpiece when the reference point is returned.

5, each coordinate back to the reference point, in general, the Z-direction coordinates are preferentially returned to zero. Make the spindle of the machine tool move away from the workpiece while observing whether the coordinates are running normally.

6. Check the machining tools on the spindle, robot, and tool magazine for abnormal conditions. If the tool position in the tool magazine is wrong, the tool is damaged, etc., it should be replaced before starting the machining.

7. Start the machine and start machining the workpiece.

Second, cnc processing center shutdown

1. Stop running the machining program and record the current P segment of the machining program executed by the machining center.

2. Move the tool on the spindle away from the machining workpiece and, if necessary, return the tool grasped by the robot to the tool magazine.

3. Move the coordinates of the machine tool to the zero point of the machine and open it to a safe position, in case it is ready to return to the reference point at the next startup.

4. Turn the manual feed trimming and rapid feed trim switch to zero to prevent the machine from moving due to misoperation.

5. Cut off the hydraulic pressure and compressed air of the machine tool.

6. Cut off the power of the machine tool CRT monitor.

7. Cut off the total power supply of the machine tool and make a record of the handover.

Third, machine tool automatic processing

Machine tool automatic machining is also called memory mode machining. It uses the machining program stored in the machining center to make the machine tool continuously process the workpiece, which is the most used operation mode in the machining center. The longer the machining center runs in the memory mode, the higher the utilization rate of the ball. For example, the horizontal flexible unit first selects the machining program in the editing state, dials the “working mode selection switch” to the memory mode, retrieves the machining program/(selects the machining program starting point/) and presses the “cycle start button”. The person automatically processes the state.

万家电竞|官网